Optimasi Proses EDM Sinking Baja HMD5 di Mesin Makino Edaf3 Laboratorium Produksi Mesin dan Perkakas

Haris Setiawan; Wawa Wahyudin

doi:10.14710/jplp.1.1.37-42

DOI: https://doi.org/10.14710/jplp.1.1.37-42

Optimasi Proses EDM Sinking Baja HMD5 di Mesin Makino Edaf3 Laboratorium Produksi Mesin dan Perkakas

Haris Setiawan , Wawa Wahyudin

Teknik Manufaktur, Politeknik Manufaktur Bandung, Indonesia

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:

Abstract

The EDM sinking process is the process of cutting non-conventional workpieces by using electric sparks that occur when two electric poles are close together, the high temperature of the electric sparks can cause the workpiece particles are eroded and release to become burr in a very small size. The cutting rate in this process is influenced by many factors, including characteristics of the material, type of electrode, cutting parameters, condition of the coolant and method of spraying the coolant. This study aims to find optimum conditions for the EDM process with HMD5 steel workpieces, by using taguchi method wich is effective in making decisions with more than one variable. After all experiments and analysis, the results obtained are spark area level 1 or 50-75, current level 3 or 12A, pulse on time level 2 or 35 ms and pulse off time level 3 or 32 ms, which are the parameters with the most optimum material rete removal. After testing the optimazion result, MRR value increase from 20.26 mm³/min to 33.08 mm³/min and we have conclusion that the taguchi method can help to optimized parameter in EDM process.

Fulltext View|Download

Keywords: EDM,HMD5, MRR, taguchi

Article Metrics:

Article Info

Section: Articles

In Vol. 5, No. 1, Januari 2023

Recent articles

Pengembangan Modul Praktikum Fisika Dasar Digital pada Materi Listrik Magnet sebagai Upaya Adaptasi Kebiasaan Baru Rancang Bangun Mesin Refrigerant Recovery untuk Meningkatkan Efisiensi R-22 pada Praktikum Sistem Refrigerasi Perbandingan Metode Arah Gerakan Elektroda terhadap Distorsi dan Kekerasan pada Hasil Pengelasan SMAW Baja Komersil More recent articles

Sidi, P., Wahyudi, M. Thoriq. 2013. Aplikasi Metoda Taguchi Untuk Mengetahui Optimasi Kebulatan Pada Proses Bubut CNC. Jurnal Rekayasa Mesin Vol.4
Asteria, Angga. Et al. 2019. Optimasi Multirespon Purwarupa Electrical Discharge Machine (EDM) Menggunakan Metode Taguchi-Grey Relational Analysis. Jurnal Teknilogi Manufaktur Vol.11
Yudo, Eko. Pratiwi, diah Kusuma. 2017. Parameter Mesin Edm Sinking Untuk Mengoptimalkan Respon Pada Material Aisi H13 Menggunakan Metode Taguchi. Prosiding Sentrinov Vol.3
Engelita, Lisbhet. Et al. 2020. Pengaruh Parameter Arus Discharge Dan Elektroda Terhadap Nilai MRR Pada Proses Sinker EDM Material Aisi. Jurnal Mekanik Terapan. Vol. 01
Handoko, Dwi. Et al. (n.d.) Analisa Parameter Arus Pemakanan Terhadap Material Removal Rate Dan Electrode Relative Wear Bahan Electrode Cu, Brass Dan Graphit Pada Mesin Edm Chimer Ez
Upara, Nafsan., Destianto, Dimas Anugrah. 2019, Pengaruh Parameter Proses Edm Sinking Terhadap Laju Pelepasan Bahan dan Laju Keausan Elektroda. Jurnal Asimetrik Vol.1.2
Soejanto, Irwan. 2009. Desain Eksperimen dengan Metode Taguchi. Graha Ilmu
Supranto, J. 1987. Statistic teori dan aplikasi. Erlangga

Last update:

No citation recorded.

Last update:

No citation recorded.

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

The Authors submitting a manuscript do so on the understanding that if accepted for publication, copyright of the article shall be assigned to Jurnal Pengelolaan Laboratorium Pendidikan and Laboratorium Technical Service Unit Integrated Laboratory Diponegoro University as publisher of the journal.

Copyright encompasses exclusive rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms and any other similar reproductions, as well as translations. The reproduction of any part of this journal, its storage in databases and its transmission by any form or media, such as electronic, electrostatic and mechanical copies, photocopies, recordings, magnetic media, etc. , will be allowed only with a written permission from Jurnal Pengelolaan Laboratorium Pendidikan and Laboratorium.

Jurnal Pengelolaan Laboratorium Pendidikan was published Technical Service Unit Integrated Laboratory Diponegoro University and the Editors make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in Jurnal Pengelolaan Laboratorium Pendidikan are sole and exclusive responsibility of their respective authors and advertisers.