Variasi Heat Treatment dalam Meningkatkan Sifat Mekanik Pahat Bubut HSS di Laboratorium Teknik Pemesinan

Yopi Yogasmana; Mutaufiq Mutaufiq; Rensinna Ilmiwar Chair

doi:10.14710/jplp.8.2.94-99

DOI: https://doi.org/10.14710/jplp.8.2.94-99

Variasi Heat Treatment dalam Meningkatkan Sifat Mekanik Pahat Bubut HSS di Laboratorium Teknik Pemesinan

Yopi Yogasmana¹

, Mutaufiq Mutaufiq¹, Rensinna Ilmiwar Chair²

¹Laboratorium Teknik Pemesinan, Fakultas Pendidikan Teknik dan Industri, Universitas Pendidikan Indonesia, Jl Dr Setiabudhi No. 229 Bandung 40154, Indonesia

²Program Studi Teknik Industri, Politeknik Bhakti Asih, Purwakarta, Indonesia

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Citation Format:

Abstract

The workpiece is shaped into a gear/shaft/hammer by cutting it with a lathe chisel while the lathe rotates at high speed. ST37 steel, a low-carbon steel, can be cut by a high-carbon steel lathe chisel. However, in reality, some lathe chisels are unable to cut ST37 steel, which is indicated by wear and even fracture at the cutting angle of the lathe chisel. The purpose of this research is to improve the mechanical properties of HSS lathe tools to make them harder and more durable. The method used in this research is an experiment by giving heat treatment at three different temperature variations: 780°C, 800°C, and 850°C. After the heat treatment, the hardness and toughness were tested.The results of the hardness test on the HSS lathe tool before heat treatment were 56.4 HRC and after heat treatment were 39.3 HRC; 39.0 HRC and 61.7 HRC. The results of the impact test on the HSS lathe tool before heat treatment were 2.8 Joules/mm2 and after heat treatment were 5.1 Joules/mm²; 4.7 Joules/mm² and 3.7 Joules/mm². Heat treatment variations at a temperature of 850°C with a holding time of 25 minutes and quenching with oil media resulted in an increase in hardness value of 5.3 HRC and an increase in toughness value of 0.9 Joules/mm².

Note: This article has supplementary file(s).

Fulltext View|Download | Research Instrument

Untitled

Subject
Type	Research Instrument
	Download (123KB) Indexing metadata

Email colleagues

Keywords: Bohler HSS lathe chisels, Heat treatment, the hardness test, the impact test

Article Metrics:

Article Info

Section: Articles

Language : EN

In Vol. 8 No. 2, Juli 2026 (Issue In Progress)

Adipura A & Nafi M. 2022. Analisa pengaruh heat treatment temperring dengan variasi waktu tahan dan media pendingin terhadap sifat mekanik baja karbon rendah. Prosiding Senakama : Vol. 01 hal. 203 – 212
Agam, S dan Tony, P. 2011. Teknik Perawatan Tentang Mesin Bubut. Semarang: Politeknik Negeri Semarang
Bayuseno AP. 2010. Kajian pustaka tentang keausan pada pahat bubut. Jurnal Rotasi: Vol.12 No.2 hal. 38 – 41
Dwipayana, dkk. 2018. Kekerasan baja karbon sedang dengan variasi suhu permukaan material. Jurnal Mettek: Vol. 04 No. 2 hal. 43 – 48
Handoyo Y. 2015. Pengaruh quenching dan tempering pada baja JIS grade S45C terhadap sifat mekanis dan struktur mikro crankshaft. Jurnal Imiah Teknik Mesin, Vol. 3, No.2 Agustus 2015 hal: 102 – 115
Hidayat W. 2019. Klasifikasi dan Sifat Material Teknik Serta Pengujian Material. Bandung
Kogoya, S. (2017). Perlakuan Panas (Heat Treatment). pp. 1–4. Ilmu Teknik Mesin
Pramata P & Yunus. 2013. Pengaruh jenis pahat, sudut pahat dan kedalaman pemakanan Terhadap tingkat kekasaran dan kekerasan pada proses bubut rata baja ST 42. JTM. Vol. 01 No.03 hal. 56-64
Rachman MRA. 2020. Analisa perbedaan kekerasan dan kekuatan tarik baja S45C dengan perlakuan quenching dan tempering pada media udara, air, dan oli untuk aplikasi poros motor roda tiga. JTM, Vol. 8 No.02 hal. 89 – 94
Riyadi S, dkk. 2016. Pengukuran Komponen-Komponen Mesin Bubut Dengan Menggunakan Metode Schlesinger. Proceeding Stima, Hal 230 – 237
Saktisahdan TJ. (2019). Pengaruh proses heat treatment terhadap perubahan struktur mikro baja karbon rendah. Jurnal Laminar. Vol. 1 No. 1 hal 28-33
Santoso EB, dkk. 2019. Pengaruh kecepatan pemakanan pengeboran dan perlakuan pendinginan terhadap kekerasan dan efisiensi mata bor pada material structural steel. Prosiding Teknik Mesin Udayana, Vol. 6 N 1, hal 48 – 53
Sidiq MF, dkk. 2022. Perlakuan panas bertingkat sebagai upaya meningkatkan kekuatan mekanik baja karbon rendah. Jurnal Sains dan Teknologi: Vol. 11 No. 1 Tahun 2022, hal. 117-124
Suherman. 2003. Ilmu Logam 1. Surabaya: ITS
Widarto. 2013. Teknik pemesinan bubut 1. Cimahi : Direktorat Pembinaan Sekolah Menengah Kejuruan Direktorat Jenderal Pendidikan Menengah Kementerian Pendidikan Dan Kebudayaan. Hal: 17

Last update:

No citation recorded.

Last update:

No citation recorded.

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

The Authors submitting a manuscript do so on the understanding that if accepted for publication, copyright of the article shall be assigned to Jurnal Pengelolaan Laboratorium Pendidikan and Laboratorium Technical Service Unit Integrated Laboratory Diponegoro University as publisher of the journal.

Copyright encompasses exclusive rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms and any other similar reproductions, as well as translations. The reproduction of any part of this journal, its storage in databases and its transmission by any form or media, such as electronic, electrostatic and mechanical copies, photocopies, recordings, magnetic media, etc. , will be allowed only with a written permission from Jurnal Pengelolaan Laboratorium Pendidikan and Laboratorium.

Jurnal Pengelolaan Laboratorium Pendidikan was published Technical Service Unit Integrated Laboratory Diponegoro University and the Editors make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in Jurnal Pengelolaan Laboratorium Pendidikan are sole and exclusive responsibility of their respective authors and advertisers.