Rancang Bangun Mesin CNC PCB Berbasis Arduino Untuk Mendukung TEFA Jurusan Teknik Informatika

Fendi Hermawanto; Hilda Jaya Habibi

doi:10.14710/jplp.7.2.73-80

DOI: https://doi.org/10.14710/jplp.7.2.73-80

Rancang Bangun Mesin CNC PCB Berbasis Arduino Untuk Mendukung TEFA Jurusan Teknik Informatika

Fendi Hermawanto¹ , Hilda Jaya Habibi²

¹Jurusan Teknik Informatika, Politeknik Negeri Banyuwangi, Jl. Raya Jember Km.13 Labanasem, Kabat, Banyuwangi 68461 , Indonesia

²Jurusan Teknik Informatika, Politeknik Negeri Banyuwangi, Jl. Raya Jember Km.13 Labanasem, Kabat, Banyuwangi 68461 , Indonesia

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

BibTex Citation Data :

@article{JPLP20874,
    author = {Fendi Hermawanto and Hilda Jaya Habibi},
    title = {Rancang Bangun Mesin CNC PCB Berbasis Arduino Untuk Mendukung TEFA Jurusan Teknik Informatika},
    journal = {Jurnal Pengelolaan Laboratorium Pendidikan},
  volume = {7},
    number = {2},
    year = {2025},
    keywords = {Tefa; CNC; PCB},
    abstract = { The State Polytechnic of Banyuwangi in the Strategic Plan 2020-2024 has a target to improve the quality of the curriculum and learning. To achieve these goals, a strategy is to establish a Teaching Factory (TeFa). One of the rapidly growing industries today is the Printed Circuit Board (PCB) manufacturing industry. This is evidenced by the presence of PCB printing websites such as Indomaker and marketplaces like Tokopedia and Bukalapak, which provide PCB printing services according to customer preferences with fast turnaround times. The research supported the development of the Teaching Factory in the Department of Informatics Engineering, Computer Engineering Technology study program. This will be achieved by increasing the number of CNC PCB machines to create a working system that closely resembles real industry conditions. The method used is the Research and Development (R&D) method, which is used to develop a product and test its effectiveness. During the testing of the X, Y, and Z axis movements, the CNC PCB machine was found to move according to the instructions provided by the Candle Software. In the testing of the PCB trace printing configuration using a V 30° router drill bit, the best results were obtained using a Cut Z of 0.15 mm and a Feed Rate of 20 mm/minute. The presence of the CNC PCB machine will facilitate the TEFA of the Department of Informatics Engineering in creating prototypes of a product before it enters the production stage.. },
   issn = {2654-251X},   pages = {73--80}  doi = {10.14710/jplp.7.2.73-80},
    url = {https://ejournal2.undip.ac.id/index.php/jplp/article/view/20874}
}

Citation Format:

Abstract

The State Polytechnic of Banyuwangi in the Strategic Plan 2020-2024 has a target to improve the quality of the curriculum and learning. To achieve these goals, a strategy is to establish a Teaching Factory (TeFa). One of the rapidly growing industries today is the Printed Circuit Board (PCB) manufacturing industry. This is evidenced by the presence of PCB printing websites such as Indomaker and marketplaces like Tokopedia and Bukalapak, which provide PCB printing services according to customer preferences with fast turnaround times. The research supported the development of the Teaching Factory in the Department of Informatics Engineering, Computer Engineering Technology study program. This will be achieved by increasing the number of CNC PCB machines to create a working system that closely resembles real industry conditions. The method used is the Research and Development (R&D) method, which is used to develop a product and test its effectiveness. During the testing of the X, Y, and Z axis movements, the CNC PCB machine was found to move according to the instructions provided by the Candle Software. In the testing of the PCB trace printing configuration using a V 30° router drill bit, the best results were obtained using a Cut Z of 0.15 mm and a Feed Rate of 20 mm/minute. The presence of the CNC PCB machine will facilitate the TEFA of the Department of Informatics Engineering in creating prototypes of a product before it enters the production stage..

Fulltext View|Download

Keywords: Tefa; CNC; PCB

Article Metrics:

Article Info

Section: Articles

Language : ID

In Vol. 7 No. 2, Juli 2025

Recent articles

Rancang Bangun Mesin CNC PCB Berbasis Arduino Untuk Mendukung TEFA Jurusan Teknik Informatika More recent articles

Arduino. (2023, 11 10). What is Arduino? Retrieved from www.arduino.cc: www.arduino.cc/en/Guide/Introduction
Hasibuan, M. R., Muhaimin, & Hardi, S. (2019). Rancang Bangun Mesin CNC Mikking 3-Axis untuk Anggrave PCB Berbasis Arduino Uno. Jurnal Tektro, Vol.3, No.1
Irawan Malik, A. S. (2019). Pengaruh Spindle Speed, Feed Rate, Dan Depth Of Cut Terhadap Akurasi Hasil Permesinan Pada Mesin Cnc Router 3 Sumbu. Jurnal Austenit, VOL 11, NO 2
Lutfiyana, N. H. (2017). Rancang Bangun Alat Ukur Suhu Tanah, Kelembaban Tanah, dan Resistansi. Jurnal Teknik Elektro, Volume 9 No.2
Prashil N Patel, S. D. (2019). Design and Development of Portable 3-Axis CNC Router Machine. International Research Journal of Engineering and Technology (IRJET), Volume: 06 Issue: 03
Putra, O. A. (2020). Pengembangan Produk Ukir Berbasis 3 Dimensi Untuk Mesin CNC. Jurnal KomtekInfo, 293-301
Supriyati, T. P. (2023). Rancang Bangun CNC (Computer Numerical Control) Untuk Pembuatan PCB Berbasis Arduino. Orbith, 43-49
Zulkarnain, & Suprianto, B. (2019). Rancang Bangun Mesin Pcb Milling Dengan Konfigurasi Kartesian Robot 3 Aksis. Jurnal Teknik Elektro, 587-593

Last update:

No citation recorded.

Last update:

No citation recorded.

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

The Authors submitting a manuscript do so on the understanding that if accepted for publication, copyright of the article shall be assigned to Jurnal Pengelolaan Laboratorium Pendidikan and Laboratorium Technical Service Unit Integrated Laboratory Diponegoro University as publisher of the journal.

Copyright encompasses exclusive rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms and any other similar reproductions, as well as translations. The reproduction of any part of this journal, its storage in databases and its transmission by any form or media, such as electronic, electrostatic and mechanical copies, photocopies, recordings, magnetic media, etc. , will be allowed only with a written permission from Jurnal Pengelolaan Laboratorium Pendidikan and Laboratorium.

Jurnal Pengelolaan Laboratorium Pendidikan was published Technical Service Unit Integrated Laboratory Diponegoro University and the Editors make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in Jurnal Pengelolaan Laboratorium Pendidikan are sole and exclusive responsibility of their respective authors and advertisers.