Impact of AlCl3 and FeCl2 Addition on Catalytic Behaviors of TiCl4/MgCl2/THF Catalysts for Ethylene Polymerization and Ethylene/1-Hexene Copolymerization
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
The present research focuses on elucidating of the impact of Lewis acids including AlCl3 and FeCl2 addition on catalytic behaviors during ethylene polymerization and ethylene/1-hexene copolymerization over the TiCl4/MgCl2/THF catalyst (Cat. A). In this study, the Cat. A with the absence and presence of Lewis acids was synthesized via the chemical route. Then, all catalyst samples were characterized and tested in the slurry polymerization. For ethylene polymerization, using the Cat. A with the presence of AlCl3 apparently gave the highest activity among other catalysts. In addition, the activity of catalysts tended to increase with the presence of the Lewis acids. This can be attributed to an enhancement of active center distribution by the addition of Lewis acids leading to larger amounts of the isolated Ti species. Moreover, with the presence of Lewis acids, the effect of hydrogen on the decreased activity was also less pronounced. Considering ethylene/1-hexene copolymerization, it revealed that the catalyst with the presence of mixed Lewis acids (AlCl3 + FeCl2) exhibited the highest activity. It is suggested that the presence of mixed Lewis acids possibly caused a change in acidity of active sites, which is suitable for copolymerization. However, activities of all catalysts in ethylene/1-hexene copolymerization were lower than those in ethylene polymerization. The effect of hydrogen on the decreased activity for both polymerization and copolymerization system was found to be similar with the presence of Lewis acids. Based on this study, it is quite promising to enhance the catalytic activity by addition of proper Lewis acids, especially when the pressure of hydrogen increases. The characteristics of polymers obtained upon the presence of Lewis acids will be discussed further in more detail. Copyright © 2018 BCREC Group. All rights reserved
Received: 22nd January 2018; Revised: 18th March 2018; Accepted: 19th March 2018
How to Cite: Niyomthai, T., Jongsomjit, B., Praserthdam, P. (2018). Impact of AlCl3 and FeCl2 Addition on Catalytic Behaviors of TiCl4/MgCl2/THF Catalysts for Ethylene Polymerization and Ethylene/1-Hexene Copolymerization. Bulletin of Chemical Reaction Engineering & Catalysis, 13 (3): 393-404 (doi:10.9767/bcrec.13.3.2116.393-404)
- Lee, T., Kim, W.K., Lee, Y., Ryou, M.H., Lee, Y.M. (2014). Effect of Al2O3 Coatings Prepared by RF Sputtering on Polyethylene Separators for High-Power Lithium Ion Batteries. Macromol. Res., 22: 1190-1195.
- Jeon, M., Han, C.J., Kim, S.Y. (2006). Poly-merizations of Propylene with Unsymmetrical (α-Diimine)nickel(II) Catalysts. Macromol. Res., 14: 306-311.
- Phiwkliang, W., Jongsomjit, B., Praserthdam, P. (2014). Synergistic Effects of the ZnCl2-SiCl4 Modified TiCl4/MgCl2/THF Catalytic System on Ethylene/1-Hexene and Ethylene/1-Octene Copolymerizations. Chin. J. Polym. Sci., 32: 84-91.
- Wannaborworn, M., Praserthdam, P., Jongsomjit, B., Cai, Z., Yano, H., Shiono, T. (2013). Copolymerization of Ethylene and 1‐Hexene with Ansa‐Dimethylsilylene (fluorenyl)(t‐butylamido) Dimethyltitanium Complexes Activated by Modified Methyl-aluminoxane. Macromol. Chem. Phys., 214: 2584-2590.
- Xia, S., Fu, Z., Huang, B., Xu, J., Fan, Z. (2012). Ethylene/1-Hexene Copolymerization with MgCl2-supported Ziegler–Natta Catalysts Containing Aryloxy Ligands. Part I: Catalysts Prepared by Immobilizing TiCl3(OAr) onto MgCl2 in Batch Reaction. J. Mol. Catal. A: Chem., 355: 161-167.
- Czaja, K., Białek, M., Utrata, A. (2004). Copolymerization of Ethylene with 1‐Hexene over Metallocene Catalyst Supported on Complex of Magnesium Chloride with Tetrahydrofuran. J. Polym. Sci. Part A: Polym. Chem., 42: 2512-2519.
- Czaja, K., Białek, M. (2001). Microstructure of Ethylene-1-Hexene and Ethylene-1-Octene Copolymers Obtained over Ziegler–Natta Catalysts Supported on MgCl2(THF)2. Polym., 42: 2289-2297.
- Britto, M.L., Galland, G.B., dos Santos, J.H.Z., Forte, M.C. (2001). Copolymerization of Ethylene and 1-Hexene with Et(Ind)2 ZrCl2 in Hexane. Polym., 42: 6355-6361.
- Jantasee, S., Shiono, T., Jongsomjit, B. (2013). Copolymerization of Ethylene/1-Hexene with Zirconocene/MAO Catalyst Supported on Spherical Zirconia Modified with BCl3, SiCl4, and Glycerol. Polym. Bull., 70: 1753-1768.
- Wannaborworn, M., Jongsomjit, B. (2009). Ethylene/1-Octene Copolymerization over Ga-modified SiO2-supported Zirconocene/MMAO Catalyst using in Situ and Ex Situ Impregnation Methods. Iran. Polym. J., 18: 969-979.
- Chen, Y.P., Fan, Z.Q. (2006). Ethylene/1-Hexene Copolymerization with TiCl4/MgCl2/AlCl3 Catalyst in the Presence of Hydrogen. Eur. Polym. J., 42: 2441-2419.
- Xia, S.J., Fu, Z.S., Liu, X.Y., Fan, Z.Q. (2013). Copolymerization of Ethylene and 1-Hexene with TiCl4/MgCl2 Catalysts Modified by 2,6-Diisopropylphenol. Chin. J. Polym. Sci., 31: 110-121.
- Mulhaupt, R., Ovenall, D.W., Ittel, S.D. (1988). Control of Composition in Ethylene Copolymerizations using Magnesium Chloride Supported Ziegler–Natta Catalysts. J. Polym. Sci. Part A: Polym. Chem., 26: 2487-2500.
- Kong, Y., Yi, J., Dou, X., Liu, W., Huang, Q., Gao, K. (2010). With Different Structure Ligands Heterogeneous Ziegler–Natta Catalysts for the Preparation of Copolymer of Ethylene and 1-Octene with High Comonomer Incorporation. Polym., 51: 3859-3866.
- Luo, H.K., Tang, R.G., Gao, K.J. (2002). Studies on the Formation of New, Highly Active Silica-Supported Ziegler–Natta Catalyst for Ethylene Polymerization. J. Catal., 210: 328-339.
- Carlini, C., D'Alessio, A., Giaiacopi, S., Po, R., Pracella, M., Galletti, A.M.R. (2007). Linear Low-Density Polyethylenes by Co-polymerization of Ethylene with 1-Hexene in the Presence of Titanium Precursors and Organoaluminium Co-catalysts. Polym., 48: 1185-1192.
- Coutinho, F.M.B., Xavier, J.L. (1997). Properties of Ethylene-Propylene Copolymers Synthesized by a Supported Ziegler-Natta Catalyst Based on TiCl4/MgCl2/PCl3. Eur. Polym. J., 33: 897-901.
- Wang, W., Wang, L., Chen, T., Sun, T.X., Wang, J.J., Chen, X. (2006). Low Isotactic Polypropylene Synthesized with a MgCl2/AlCl3-Supported Ziegler Catalyst. J. Mol. Catal. A: Chem., 244: 146-150.
- Chu, K.J., Chang, H.S., Ihm, S.K. (1994). Effects of Diethyl Aluminum Chloride (DEAC) Addition to the Catalysts Prepared by Reduction of TiCl4 with EtMgCl on Ethylene-Propylene Copolymerization. Eur. Polym. J., 30:.1467-1472.
- Kim, J.H., Han, T.K., Choi, H.K., Kim, I., Woo, S.I. (1995). Copolymerization of Ethylene and 1-Butene with Highly Active TI/MG Bimetallic Catalysts. Effect of Partial Activation by AlEt2Cl. Macromol. Rapid Commun., 16: 113-118.
- Magalhaes, D.T., Do Coutto Filho, O., Coutinho, F. (1991). Ziegler-Natta Catalyst for Ethylene and Propylene Polymerization Supported on Adducts of Magnesium Chloride with Methyl and Ethyl Alcohols. Eur. Polym. J., 27: 827-830.
- Grau, E., Lesage, A., Norsic, S., Copéret, C., Monteil, V., Sautet, P. (2012). Tetrahydrofuran in TiCl4/THF/MgCl2: a Non-Innocent Ligand for Supported Ziegler–Natta Polymerization Catalysts. ACS Catal., 3: 52-56.
- Huang, R., Malizia, F., Pennini, G., Koning, C.E., Chadwick, J.C. (2008). Effects of MgCl2 Crystallographic Structure on Active Centre Formation in Immobilized Single‐Centre and Ziegler–Natta Catalysts for Ethylene Polymerization. Macromol. Rapid Commun., 29: 1732-1738.
- Chang, H.S., Song, W.D., Chu, K.J., Ihm, S.K. (1992). Effects of Removing THF from the TiCl3 (AA)/3MgCl2/THF Catalyst System on the Ethylene-Propylene Copolymerization Mechanism. Macromol., 25: 2086-2092.
- Phiwkliang, W., Jongsomjit, B., Praserthdam, P. (2013). Effect of ZnCl2‐and SiCl4‐doped TiCl4/MgCl2/THF Catalysts for Ethylene Polymerization. J. Appl. Polym. Sci., 130: 1588-1594.
- Seenivasan, K., Sommazzi, A., Bonino, F., Bordiga, S., Groppo, E. (2011). Spectroscopic Investigation of Heterogeneous Ziegler–Natta Catalysts: Ti and Mg Chloride Tetrahydrofuranates, Their Interaction Compound, and the Role of the Activator. Chem. Eur. J., 17: 8648-8656.
- Pothirat, T., Jongsomjit, B., Praserthdam, P. (2008). Effect of Zr-modified SiO2-supported Metallocene/MAO Catalyst on Copolymerization of Ethylene/1-Octene. Catalysis Letters, 121: 266-273.
- Sudsong, N., Phiwkliang, W., Jongsomjit, B., Praserthdam, P. (2015). Effects of Various Mixed Metal Chlorides-AlCl3 in TiCl4/MgCl2/THF Catalytic System on Ethylene Polymerization. ASEAN Journal of Chemical Engineering, 2: 12-18.
- Taniike, T., Wada, T., Kouzai, I., Takahashi, S., Terano, M. (2010). Role of Dispersion State of Ti Species in Deactivation of MgCl2-supported Ziegler-Natta Catalysts. Macromol. Res., 18: 839-844.
- Niyomthai, T., Ratchadaphet, A., Jongsomjit, B., Praserthdam, P. (2018). Influence of Hydrogen on Catalytic Properties of Ziegler‐Natta Catalysts Prepared by Different Methods in Ethylene Polymerization. Adv. Polym. Tech. 37(4): 1030-1035 DOI: 10.1002/adv.21753.
- Kissin, Y., Mink, R., Nowlin, T. (1999). Ethylene Polymerization Reactions with Ziegler–Natta Catalysts. I. Ethylene Polymerization Kinetics and Kinetic Mechanism. J. Polym. Sci. Part A: Polym. Chem., 37: 4255-4272.
- Kouzai, I., Liu, B., Wada, T., Terano, M. (2007). Effects of Hydrogen for Different Stereospecific Active Sites on Ultra Low TiCl3 Loading Supported Catalyst. Macromol. React. Eng., 1: 160-164.
- Kissin, Y.V., Mink, R.I., Nowlin, T.E., Brandolini, A.J. (1999). Kinetics and Mechanism of Ethylene Homopolymerization and Copolymerization Reactions with Heterogeneous Ti-based Ziegler–Natta Catalysts. Top Catal., 7: 69-88.
- Li, K.T., Dai, C.L., Li, C.Y. (2010). Synthesis of Linear Low Density Polyethylene with a Nano-Sized Silica Supported Cp2ZrCl2/MAO Catalyst. Polym. Bull., 64: 749-759.
- Brandolini, A.J., Hills, D.D. (2000). NMR Spectra of Polymers and Polymer Additives: CRC Press.
- Parvez, M.A., Rahaman, M., Suleiman, M., Soares, J., Hussein, I. (2014). Correlation of Polymerization Conditions with Thermal and Mechanical Properties of Polyethylenes Made with Ziegler-Natta Catalysts. Int. J. Polym. Sci. Article ID: 549031, 10 pages.
- Quijada, R., Scipioni, R.B., Mauler, R.S., Galland, G.B., Miranda, M.S. (1995). Synthesis and Characterization of Ethylene-1-Hexene Copolymers using Homogeneous Ziegler-Natta Catalysts. Polym. Bull., 35: 299-306.
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
As a journal Author, you have rights for a large range of uses of your article, including use by your employing institute or company. These Author rights can be exercised without the need to obtain specific permission.
Authors publishing in BCREC journals have wide rights to use their works for teaching and scholarly purposes without needing to seek permission, including: use for classroom teaching by Author or Author's institutionand presentation at a meeting or conference and distributing copies to attendees; use for internal training by author's company; distribution to colleagues for their reseearch use; use in a subsequent compilation of the author's works; inclusion in a thesis or dissertation; reuse of portions or extrcats from the article in other works (with full acknowledgement of final article); preparation of derivative works (other than commercial purposes) (with full acknowledgement of final article); voluntary posting on open web sites operated by author or author’s institution for scholarly purposes (follow CC by SA License).
Authors and readers can copy and redistribute the material in any medium or format, as well as remix, transform, and build upon the material for any purpose, even commercially, but they must give appropriate credit (cite to the article or content), provide a link to the license, and indicate if changes were made. If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original.
Copyright Transfer Agreement
The Authors submitting a manuscript do so on the understanding that if accepted for publication, copyright publishing of the article shall be assigned to Bulletin of Chemical Reaction Engineering & Catalysis journal and Department of Chemical Engineering Diponegoro University as publisher of the journal.
Copyright encompasses exclusive rights to reproduce and deliver the article in all form and media, including reprints, photographs, microfilms and any other similar reproductions, as well as translations. The reproduction of any part of this journal, its storage in databases and its transmission by any form or media, such as electronic, electrostatic and mechanical copies, photocopies, recordings, magnetic media, etc., will be allowed only with a written permission from Bulletin of Chemical Reaction Engineering & Catalysis journal and Department of Chemical Engineering Diponegoro University.
Bulletin of Chemical Reaction Engineering & Catalysis journal and Department of Chemical Engineering Diponegoro University, the Editors and the Advisory International Editorial Board make every effort to ensure that no wrong or misleading data, opinions or statements be published in the journal. In any way, the contents of the articles and advertisements published in the Bulletin of Chemical Reaction Engineering & Catalysis are sole and exclusive responsibility of their respective authors and advertisers.
Remember, even though we ask for a transfer of copyright, our journal authors retain (or are granted back) significant scholarly rights.
The Copyright Transfer Form can be downloaded here: [Copyright Transfer Form BCREC 2016]
The copyright form should be signed originally and send to the Editorial Office in the form of original mail, scanned document or fax :
Prof. Dr. I. Istadi (Editor-in-Chief)
Editorial Office of Bulletin of Chemical Reaction Engineering and Catalysis
Department of Chemical Engineering, Diponegoro University
Jl. Prof. Soedarto, Kampus Undip Tembalang, Semarang, Central Java, Indonesia 50275
Telp.: +62-24-7460058, Fax.: +62-24-76480675